RE: [squid-users] 2.6S1 WCCP2 problems http_port 3128 transparent
vhost vport=80
tcp_outgoing address 10.10.10.1
wccp2_router 10.10.10.2
wccp2_forwarding_method 1
wccp2_return_method 1
wccp2_service standard 0
As far I know, kernel 2.6.9 & up , you do need bringing up loopback0 at
cisco router (this is because wccp will use it as router identifier)
#at router :
interface lo0
ip address 172.0.0.1 255.255.255.252
no shut
#-at squid:
insmod ip_gre
ifconfig gre0 up
ip addr add 172.0.0.2 255.255.255.252 dev gre0
If you shut loopback0, wccp mechanism still alive at router, but no traffic
being redirected ( gre_tunnel is established between lo0<-->gre0 & via this
tunnel where web-traffic redirected)
Also put "ip wccp web-cache exclude in" in the router interface where squid
attached & make sure it is not same vlan where traffic redirected
regards
Tino
----- Original Message -----
From: Shoebottom, Bryan
To: tino ; squid-users@squid-cache.org
Sent: Tuesday, July 18, 2006 7:06 PM
Subject: RE: [squid-users] 2.6S1 WCCP2 problems
Tino,
Our lookback interface is not configured and never has been in the past for
caches to work. You do bring up an interesting point of the IP address of
the gre interface. In the past i have simply used an IP that is not on our
network, maybe i can't do that anymore. What wccp directives do you have
configured in your squid.conf?
Thanks,
Bryan
-----Original Message-----
From: tino [mailto:tino.kriswanto@gmail.com]
Sent: Mon 7/17/2006 8:17 PM
To: Shoebottom, Bryan; squid-users@squid-cache.org
Subject: Re: [squid-users] 2.6S1 WCCP2 problems
Hi, Bryan
what is your interface loopback0 status & ip address at L3 6500 ? It should
be in the same subnet with your gre0 ip address.
I'm running 6500 earlier version than yours (supervisor engine-1a & msfc1),
ip cef enable, & wccpv2 work ok with squid-2.6S1, I'm using kernel 2.6.15.7
with ip_gre loaded from kernel module.
It also work when I put squid-2.6.S1 with 3620 router, ios 12.2(t) &
as5300, ios 12.0.7(t)
also, make sure iptables loaded first before running squid
rgds,
Tino
----- Original Message -----
From: Shoebottom, Bryan <mailto:BShoebottom@fanshawec.ca>
To: tino <mailto:tino.kriswanto@gmail.com> ;
squid-users@squid-cache.org
Sent: Monday, July 17, 2006 7:29 PM
Subject: RE: [squid-users] 2.6S1 WCCP2 problems
-6500 running code 12.1(26)E
-ip wccp we redirect in configured on vlans
ip wccp web-cache
-2.6.17
-/sbin/iptables -t nat -A PREROUTING -i gre0 -p tcp -m tcp --dport
80 -j REDIRECT --to-ports 3128
eth0 Link encap:Ethernet HWaddr 00:14:C2:C3:3B:1D
inet addr:10.10.101.3 Bcast:10.10.101.7
Mask:255.255.255.248
inet6 addr: fe80::214:c2ff:fec3:3b1d/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:53302 errors:0 dropped:0 overruns:0 frame:0
TX packets:41745 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:7311146 (6.9 MiB) TX bytes:6586185 (6.2 MiB)
Interrupt:185
gre0 Link encap:UNSPEC HWaddr
00-00-00-00-BD-BF-A8-4C-00-00-00-00-00-00-00-00
inet addr:10.2.1.1 Mask:255.255.255.252
UP RUNNING NOARP MTU:1476 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:104 errors:0 dropped:0 overruns:0 frame:0
TX packets:104 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:19992 (19.5 KiB) TX bytes:19992 (19.5 KiB)
I have enabled wccp2 when configuring squid.
Thanks,
Bryan
-----Original Message-----
From: tino [mailto:tino.kriswanto@gmail.com]
Sent: Sun 7/16/2006 11:11 PM
To: Shoebottom, Bryan; squid-users@squid-cache.org
Subject: Re: [squid-users] 2.6S1 WCCP2 problems
give me this data :
-cisco router version & ios version
-cisco runnning config
-kernel version
-iptables setting
-output of ifconfig
-when ./configure , your need add this options --enable_wccpv2
rgds,
Tino
----- Original Message -----
From: "Shoebottom, Bryan" <BShoebottom@fanshawec.ca>
To: <squid-users@squid-cache.org>
Sent: Saturday, July 15, 2006 1:27 AM
Subject: RE: [squid-users] 2.6S1 WCCP2 problems
Does anyone have this problem on 2.6S1???
With debug on on the router I get this error:
Here_I_Am packet from 10.10.101.3 w/bad rcv_id 00000000
Any help would be appreciated.
Thanks,
Bryan
-----Original Message-----
From: Shoebottom, Bryan [mailto:BShoebottom@fanshawec.ca]
Sent: July 13, 2006 1:18 PM
To: squid-users@squid-cache.org
Subject: [squid-users] 2.6S1 WCCP2 problems
Hey,
I can't seem to get wccpv2 working in squid 2.6Stable1. My wccp
config is
as follows:
wccp2_router 10.10.101.1
wccp2_forwarding_method 1
wccp2_return_method 1
wccp2_service standard 0
My router only seems to see L2 redirection even though I have
specified
GRE/WCCP:
ROUTER#sho ip wcc we d
WCCP Cache-Engine information:
Web Cache ID: 10.10.101.3
Protocol Version: 2.0
State: NOT Usable
Redirection: L2
Packet Return: L2
Packets Redirected: 0
Connect Time: 00:00:29
Assignment: MASK
ROUTER#
After 30 seconds, the connect time for the cache restarts. I am
running a
2.6.17 kernel which supports WCCP in the GRE module and have this
loaded as
gre0.
Has anyone else gotten this to work under the new 2.6 release yet?
Anyone
have any suggestions?
Thanks,
Bryan
Received on Tue Jul 18 2006 - 18:26:27 MDT
This archive was generated by hypermail pre-2.1.9 : Tue Aug 01 2006 - 12:00:01 MDT